STLINK-V3MINIE top, bottom, and
cable views. Picture is not contractual.
Features
• Stand-alone probe
• Approximately 15 × 42 mm high-density integration PCB
• USB 2.0 high-speed interface
• Drag-and-drop Flash memory programming (optional)
• Two LEDs: communication, power (not fitted)
• Probe firmware update through USB
• JTAG/SWD (Serial Wire Debug) specific features:
– 1.65 to 3.6 V application voltage support
– JTAG communication support
– SWD and serial wire viewer (SWV) communication support
– Input/output level shifters for SWD/SWV/JTAG STM32 MCU signals
• Virtual COM port (VCP) specific features:
– 1.65 to 3.6 V application voltage support on the UART interface
– VCP frequency up to 15 MHz
– Input/output level shifters for VCP (UART) signals
• Board connectors:
–
Self-powered through a USB Type-C
®
connector
– 1.27 mm pitch STDC14 signal‑protected debug connector with STDC14 to
STDC14 flat cable
– 2.0 mm pitch on-board pads on both sides for board-to-board (BTB) card
edge connector
Description
STLINK-V3MINIE is a stand-alone debugging and programming tiny probe for
STM32 microcontrollers.
The JTAG/SWD interfaces are used to communicate with any STM32 microcontroller
located on an application board.
STLINK-V3MINIE also provides a Virtual COM port interface for the host PC to
communicate with the target microcontroller through one UART.
STLINK-V3MINIE is a portable version, easy‑to‑use debugger and programmer
including STDC14 interface with its flat cable and pads on board for board‑to‑board
(BTB) card edge connector.
Product status link
STLINK-V3MINIE
STLINK-V3MINIE debugger/programmer tiny probe for STM32 microcontrollers
STLINK-V3MINIE
Data brief
DB4541 - Rev 1 - September 2021
For further information contact your local STMicroelectronics sales office.
www.st.com
1 Ordering information
To order the STLINK-V3MINIE tiny probe, refer to Table 1. For a detailed description of the board, refer to its user
manual on the product web page.
Table 1. Ordering information
Order code Content and references User manual Description
STLINK-V3MINIE
• MB1762
(1)
• FFC
(2)
UM2910
• STLINK-V3MINIE in-circuit debugger and
programmer for STM32 with level shifter
• STM32 board featuring a 2 × 7 pin ZIF
connector
1. Tiny probe board.
2. Flexible flat cable.
1.1 Product marking
The stickers located on the top or bottom side of the PCB provide product information:
• Product order code and product identification for the first sticker
• Board reference with revision, and serial number for the second sticker
On the first sticker, the first line provides the product order code, and the second line the product identification.
On the second sticker, the first line has the following format: “MBxxxx-Variant-yzz”, where “MBxxxx” is the board
reference, “Variant” (optional) identifies the mounting variant when several exist, "y" is the PCB revision and "zz"
is the assembly revision, for example B01. The second line shows the board serial number used for traceability.
Evaluation tools marked as “ES” or “E” are not yet qualified and therefore not ready to be used as reference
design or in production. Any consequences deriving from such usage will not be at ST charge. In no event, ST will
be liable for any customer usage of these engineering sample tools as reference designs or in production.
“E” or “ES” marking examples of location:
• On the targeted STM32 that is soldered on the board (For an illustration of STM32 marking, refer to the
STM32 datasheet “Package information” paragraph at the www.st.com website).
• Next to the evaluation tool ordering part number that is stuck or silk-screen printed on the board.
STLINK-V3MINIE
Ordering information
DB4541 - Rev 1
page 2/5
